Pneumatics Training System

Product Name : Pneumatics Training System

Model : LA-PNS-I

Feature:
Pneumatic training device is at the request of modern pneumatic professional teaching experiment, according to “the hydraulic and pneumatic transmission “, “the Pneumatic control technology”, etc., general teaching material contents design. The system in Addition

 Meet the base and teaching training system of need of practical applications
 Equipment structure is firm and has good stability
 Low noise operation
 layout clear and intriguing design
 The four truckle with crack slot in order to move and install on the work table. Panel grooves intervals are 25 mm, can easily move all kinds
of components insert on it.
 Various pneumatic components into separate module which is equipped with bottom panel of elastic pins, when training they can build all
kinds of pneumatic circuits on general aluminum, fast loading and unloading, flexible layout, clear pneumatic circuit
 Electrical control units used for independent relay control unit and multi-button unit control electrical, simple and clear!
 High safety: have over-current protection, the power supply will cut off as earth leakage exceed 30mA; the electrical control use DC 24v
power supply, with over current protection, can prevent damage to the equipment caused by improper operation .system nominal pressure
is 0.6MPa.

Pneumatic basic control circuit experiment:

Single acting cylinder automatic control,
 Double acting cylinder automatic control,
 PLC control technical application
 Relay control technical application
 Other comprehensiveness, expansibility experiment type pneumatic circuit.

Structural composition:

Aluminum basal plate, electric control cabinet, PLC hung box, Operation panel, Pneumatic cylinder, charging barrel, magnetic valves, Mini
cylinder, vacuum chuck, parallel lines Groove, I/O switch over Module, Air controller.
Main electrical components:
-Illuminated push button stop/start: LAY50-22D one open DC24V (or Equivalent)
-Button signs : 22 mm
-Fiber optic sensor amplifiers: 6 bets
-Fiber optic sensor Amplifiers: PNP DC24V
-The receiver transmitter (generator): PNP DC24V
-Dimension: minimum (Length x width x height)- 450mm x 790mm x 1260mm

Pneumatic basic experiment circuits illustrate:

 Single acting cylinder reversing circuit,
 Double acting cylinder reversing circuit,
 Single acting cylinder speed control circuit,
 Double acting cylinder one-way speed regulation circuit,
 Double acting cylinder both-way speed regulation circuit,
 Speed changing-over circuit,
 Buffering circuit,
 Twice pressure control circuit,
 High and low voltage convert circuit,
 Delay circuit,
 Overload protection circuit,
 Interlocking circuit,
 Single cylinder single reciprocating control circuit,
 Single cylinder continuous reciprocating action circuit,
 Multi cylinder sequence action circuit
 Double-cylinder synchronization action circuit,
 Unloading circuit,
 Or gate type valve shuttle application circuit ,
 And gate application circuit of double press valve,
 Rapid exhaust valve application circuit,
 Magnetic induction type proximity switch application;
 Sensor application in control system;
 Relay control circuit

Specification:

 DC power: input, AC220V, 50Hz/60 Hz Output: DC 24V/3A
 Air compressor (basic equipment minimal machine): power: AC 220V±10% 50Hz/60Hz motor power: 600W
 Nominal volume: 9L normal output voltage 0.7 MPa, noise degree: 66 dB
 Groove interval: 25mm
 Table top structure: 1
 With crack slot truckle: 4
 Relay module:
coil voltage: DC 24V;
contactor type: circuit common-NO-NC
Contact capacity: AC 240V/10A/DC24V/10A
 Button module: Signal lamp power supply :DC 24V
Contact capacity: AC220V/1A DC24V/2A
Mechanical electrical life: 1 million times
 Workbench experiment table Dimension1360 （length）×650 （width）×1650 （height Aluminum panel dimension:1200×600
 Manifold Block Working pressure： 0.5MPa Max pressure：0.8MPa input： φ6 output：φ4； one-way
 Double-acting cylinder Cylinder diameter：20mmstroke：100mmworking pressure range：0.1~1MPaa
 Single-acting cylinder: diameter：20mm
stroke：100mm
working pressure
range：0.1~1MPa
 5/3 solenoid directional valve central vented: DC power：DC24V Working pressure
range：0.15~0.8MPa
Drive way: electric control
 5/2 single solenoid shuttle valve: voltage：DC24V Working pressure range： 0.15~0.8MPa
Drive way: electric control
 5/2 double solenoid shuttle valve: 02 Nos
 3/2 single solenoid shuttle valve NC:01 Nos
 3/2 single solenoid shuttle valve NO: 01 Nos
 5/2 handle shuttle valve Mushroom button valves:01 No
 5/2 handle shuttle valve: 01 No
 5/3 handle shuttle valve: 01 No
 Single pneumatic control 3/2: 01 No
 Double pneumatic control 3/2 : 01 No
 Double pneumatic control 5/2 : 02 Nos
 Dyad:01 No
(Pressure regulator：0.15~0.9MPa)
 Reducing valve: 02 nos
 One-way valve: 02 nos
 Pressure gauge:02 nos
 One-way throttle valve:02 nos
 3/2 knob valve:01 no
 3/2 Stroke valve:02 nos
 Time delay valve:02 nos
 Sequence valve:01 no
 “And” gate-type dual pressure:02 nos
 “Or” gate-type shuttle valve:02 nos
 Quick escape valve:01 no
 Micro switch valve (left trigger) :02 nos
 Photoelectric Sensor:01 no
 DC power supply unit: 01 No
 HoseФ4:100ft
 4 T Valve:03 Nos
 Three connection:03 Nos
 APG reducing straight coupling:03 Nos

Accessories:

– Air Compressor-01 no
– Connecting jack 2mm & 4mm : 01 Set
– Power Cable: 01 no
– PLC to PC Communication cable: 01 Sets
– Simulation software for compatible PLC
– English Manual & CD: 01 Set